CALL 310-4328
24-HOUR EMERGENCY SERVICE
OUR BLOG

Furnace Clicking but Not Turning On? What the Clicks Mean and 7 Safe Checks

Aire One Heating & Cooling · Furnace Troubleshooting

Furnace Clicking but Not Turning On?

What each click means, seven safe checks and when a licensed technician should take over.

Furnace clicking but not turning on as a homeowner stands beside a basement furnace and listens with hands off the unit
24/7 Service
TSSA-Registered
Since 1990
All Makes Serviced
$79 Service Call*
MA Matthew Arbab, Owner of Aire One Heating & Cooling
By Matthew Arbab
Owner, Aire One Heating & Cooling · Updated November 18, 2026

The short answer: A furnace clicking but not turning on is usually trying to start and failing a safety check. The click can come from the thermostat, a control board relay, a spark igniter or the gas valve. Check the thermostat, filter, registers, outdoor vent pipes and furnace door. If it still will not light after one restart, stop and call a licensed technician. If you smell gas, leave the home first.

The thermostat is calling for heat, and from the basement comes a click. No rush of warm air follows. A furnace clicking but not turning on is one of the most common no-heat calls we take once the cold settles over Ontario, and the sound is a useful clue. Where the click comes from, and what follows it, tells you how far the furnace got before it gave up.

This guide matches each click to its likely cause and lists the checks that are safe for a homeowner, with no panels to open and no gas or wiring to touch. If the house is already getting cold, you can book a furnace visit online or call 310-HEAT at any hour.

Safety first

If you smell rotten eggs or hear hissing, do not look for the source. Leave the home right away without using phones, switches or electronics, then call Enbridge Gas at 1-866-763-5427 or 911 from a safe place outside. If a carbon monoxide alarm sounds, get everyone out and call 911 from outside.

How a Furnace Starts, Click by Click

Every time it starts, a modern gas furnace works through a checklist, and each step must pass before the next begins. Details vary by make and model, but most furnaces follow this order:

1

The thermostat calls for heat. Many thermostats click softly, and a relay on the furnace control board may click in reply.

2

The inducer fan starts. This small fan hums as it pulls air through the vent pipes. A pressure switch confirms that air is moving.

3

The igniter gets ready. A hot surface igniter glows silently. A spark igniter ticks rapidly for a few seconds.

4

The gas valve opens. You hear one firm click, then the soft whoosh of the burners lighting.

5

The flame sensor confirms the flame. If it detects no flame within seconds, the gas valve clicks shut and the furnace tries again.

6

The blower comes on. After a short delay, warm air reaches the registers.

When any step fails, the furnace stops there. Many models retry a few times, then lock out for a while. With a furnace clicking but not turning on, that lockout is protecting your home, so never try to force past it.

Furnace Clicking but Not Turning On: Match the Click to the Cause

To narrow down a furnace clicking but not turning on, stand a few steps back, keep your hands off the unit and listen through one full attempt. Then find the closest match below.

What you hearWhere the start-up stoppedWho handles it
A click at the thermostat, silence at the furnaceStep 1. The call for heat is not reaching the furnace.You first: checks 1, 2, 6 and 7
One click at the furnace, then no humStep 2. The inducer fan is not starting.Licensed technician
A hum, a click, no flame, then a repeatStep 2. The pressure switch is not seeing airflow, often because of a blocked vent pipe or drain.You first: check 5, then a professional
Fast ticking for several seconds, no flameSteps 3 and 4. The igniter sparks, but the gas does not light.Licensed technician
Click, whoosh, a few seconds of flame, click, flame outStep 5. The flame sensor is not confirming the flame.Licensed technician

Many furnaces also flash a status light behind a small window in the door. Note the pattern for your technician. Our guide to a furnace blinking light explains the codes.

For background, see our posts on why furnace igniters fail, what a dirty flame sensor does and how a furnace pressure switch works. Testing or cleaning those parts is a job for a certified gas technician. Banging or squealing instead? See furnace making noise.

7 Safe Checks for a Furnace Clicking but Not Turning On

None of these needs a tool or involves the burners, gas line or wiring. Work through them in order.

  1. Confirm the thermostat settings. It should be on Heat, with the set point a couple of degrees above room temperature and the fan on Auto.
  2. Replace weak thermostat batteries. A dim or blank screen can mean a weak signal, so the thermostat clicks but the furnace never gets a steady call. See thermostat not working.
  3. Look at the filter. Natural Resources Canada says the furnace air filter should be cleaned or replaced regularly. A clogged one can make the furnace overheat and shut down. Our guide to furnace filters covers timing.
  4. Open the registers and clear the returns. Move rugs and furniture away from supply registers and cold air returns.
  5. Check the vent pipes outside. High-efficiency furnaces breathe through plastic pipes on an outside wall. Brush snow or leaves away by hand and never chip at ice. See our furnace vent blocked by snow guide.
  6. Make sure the furnace door is closed. A safety switch cuts power when the front panel is loose, often after a filter change. The panel should sit flat. Do not remove it.
  7. Look at the power and the drain. Check that the furnace switch near the unit is on and see whether the breaker has tripped. If it has, read furnace tripping breaker first. Water near the unit points to a blocked or frozen condensate line.

Next, set the thermostat to Off, wait five minutes and set it back to Heat. Give the furnace one full attempt. If you still have a furnace clicking but not turning on, the fault is inside the cabinet, where homeowner checks end and professional furnace servicing begins.

Wall thermostat with a glowing screen in a hallway while a person in a sweater stands nearby waiting for the heat
With a furnace clicking but not turning on, thermostat settings and batteries are the first things to rule out.

What to Leave Alone

The safety controls exist to stop the gas when the burners do not light. Bypassing them removes that protection, so leave these jobs alone:

Only for a certified technician

  • Opening the burner compartment
  • Cleaning or testing igniters and sensors
  • Touching the gas valve or gas piping
  • Bypassing or resetting safety switches
  • Restarting the furnace over and over

The Technical Standards and Safety Authority (TSSA) states that under Ontario law, furnaces and fuel-fired appliances must be maintained by TSSA-registered contractors, who are required to use certified gas technicians.

When a Furnace Clicking but Not Turning On Needs a Technician

Book a visit, and leave the furnace off at the thermostat while you wait, if any of these apply:

  • The seven checks made no difference after one restart.
  • The burners light for a few seconds and go out, again and again.
  • The breaker has tripped, or the status light shows a lockout code.
  • You notice a burning smell, scorch marks or water around the unit.

A technician will read the fault code, test the ignition parts and check the venting and drain. Our HVAC servicing and repairs team works on every make, and a diagnostic visit starts with a $79 service call. See furnace repair in Markham or furnace repair in Richmond Hill for local details.

If there is no click at all, the causes differ from a furnace clicking but not turning on. Start with why is my furnace not turning on.

Keeping the Problem From Coming Back

Most ignition faults build slowly as sensors collect residue and igniters wear. Three habits catch trouble early:

  • Change the filter on schedule and keep registers and returns open.
  • Walk past the outdoor pipes after each storm. Natural Resources Canada notes that the vent terminal should be kept free from obstructions, including ice.
  • Book a yearly inspection. The Ontario government advises having fuel-burning appliances, chimneys and vents cleaned and inspected by professionals every year before cold weather sets in.

A tune-up covers the igniter, flame sensor, pressure switch and safety controls, the parts behind most cases of a furnace clicking but not turning on. Members of our maintenance and protection plans get that visit every year.

Furnace Help Across the GTA Since 1990

Aire One has served Ontario homeowners since 1990 and holds a 4.8-star Google rating from 541 reviews. Our technicians are on call 24 hours a day across the GTA, including Markham and Richmond Hill, so a furnace clicking but not turning on never has to wait until morning. When repair no longer makes sense for an older unit, we offer a free Total Home Assessment, financing and a 10-year worry-free warranty. Learn more about our HVAC company in Markham, our HVAC company in Richmond Hill or our Markham furnace repair service.

Furnace clicking but not turning on?

Leave the furnace off and let a TSSA-registered technician find the cause. We answer 24/7 across Markham, Richmond Hill and the GTA.

310-HEAT (310-4328) · 24/7 service · $79 service call*

Frequently Asked Questions

Why is my furnace clicking but not turning on?

The furnace is trying to start and stopping at one of its safety checks. The click may be the thermostat, a control board relay, a spark igniter or the gas valve. Common causes include a weak thermostat signal, a blocked vent pipe, a worn igniter or a dirty flame sensor.

Is a furnace clicking but not turning on dangerous?

Usually it is not, because the safety controls shut the gas off when the burners fail to light. If you smell rotten eggs, leave the home and call Enbridge Gas at 1-866-763-5427 or 911 from outside. If a carbon monoxide alarm sounds, get everyone out and call 911.

How many times will a furnace try to light before it locks out?

It depends on the make and model. Many furnaces try a few times, then lock out for a period. Repeated lockouts mean a part needs attention, so book a service visit.

Can I reset my furnace to stop the clicking?

You can restart it once from the thermostat by switching to Off, waiting five minutes and switching back to Heat. If the clicking returns, do not keep resetting it. Repeated restarts will not clear the fault.

Can a dirty filter cause a furnace to click and not start?

It can contribute. A clogged filter restricts airflow, which can make the furnace overheat and shut down on a safety limit. Until it cools, it may click without firing, so replace the filter first.

Sources and Helpful Resources

MA Matthew Arbab, Owner of Aire One Heating & Cooling
Matthew Arbab
Owner, Aire One Heating & Cooling

Matthew leads the Aire One Markham and Metro Toronto team, helping homeowners keep their heating systems safe and reliable through every Ontario winter. Aire One has been a TSSA-registered, Carrier Factory Authorized Dealer since 1990.

Call Now